ROQ’s New Generation of Dryers – The ROQ SAHARA

At ROQ, we are never satisfied with our machines. There is always something to improve upon, and there is always feedback we should listen to and act on. With this desire to constantly improve within our company's DNA, ROQ´s engineering team partnered up with INEGI and worked tirelessly to bring our dryer to new heights.

In order to compete at the highest level, our new dryer comes with improved energy efficiency through its reinforced insulation and stand-by mode, an increased chamber entry height of 140 mm (5,5’), noise reduction and an updated user-friendly software with a brand-new recipe saving system to adapt to different types of job curing parameters.

ROQPRINT NEXT

The automatic screen printing machine 20% more productive*.

This new automatic screen printing machine, ROQprint NEXT,

was built with unique features which only exist in high-range ROQprint machines.

ROQprint Next permits you to print between 6 and 18 colors, has a maximum print area

up to 850mmx1000mm(double index) and a maximum production of up to1200 pieces per hour.

Some of the main technical characteristics are the electric rotation with Servo AC motor,

the print heads independent lifting system and a 10 ” touchscreen.

These distinctive characteristics are responsible for a productivity increase up to 20%.

NOP would like to present the Primus 3D-FILMS Printing Method:

1. To print Primus-PLAST PF Series 2 X 3 or 2 X 2 times.

2. Going through the heat application for drying inks.

3. Hot stamping with 3D-FILMS for 150 DegreeC x 15sec

4. To tear the 3D-FILMS gently after the temperature of Step3

completely cool down or keep it back to normal temperature. Then you can see the results.

Don't tear the 3D-FILMS as them still at high temperature or warm.

Notice: Step 3~4 is the key points for making the results to be completely done.

NOP would like to present High Density Inks series

that is very thick plastisol inks formulates to produce thick,

3-D ink films with sharp edges when printed through very thick stencils.835 Hgh Density Base is very opaque,

has exceptional film strength that resists cracking and has a soft finish.

838 Super Clear High Density Base is to be used as a very clear gel

finish with glossy finish.Produce amazing 3D results.

This picture was printed by mixing between 835 & 838 through mesh no.100

NOP would like to present Glow In Dark that is a plastisol mixed with phosphorescent powder.

While absorbing light for a period of time,glow effect can be easily seen in the dark.

Light yellowish green is its original paste form by day and start glowing at night.

NOP4630 would like to present Excalibur's Solar Change Series

that are four colours ,’colourless under normal, indoor light but quickly change into bright,

vibrant colours when subjected to any ultra-violet light source like sunlight,

or even black light. The new and improved formulations change colour faster

and retain the vibrant colour longer than previous versions#Thank you for NSG

NOP would like to offer G-pro testing

that underbase with essential clear 80% + essential white 20% + pigment 5% + Xlinker JF 4 %.

The testing results as the picture.

NOP 4630 offer foil printing with water base ink foil adhesive

1.Use 100 t/inch mesh

2.Print at least 2 coats of the ink before foiling process.The ink must be thick enough

to achieve a good foil surface.Dry the first coat before applying the second.

3.Heat press the foil to the print area,where is dried to the touch,by 160 c,15 sec

4.Remove pressed foil while it is complete cooled off

5.Wash after 24 hours

Water Based Retroflec (5700) is highly reflective water-based ink for safety and fashion wear

that is available in silver and white. Reflective white can be used as is, on top of colors,

or pigmented to create dazzling reflective colors.

1.Aqua Pro-Retroflec reflective ink, print/flash/print through 110 mesh (43T)

2.Using a conveyor dryer, bring imprint to a cured state 320F (160)

Remark: To ensure maximum washfastness Add2% aquafix water based fixative.

This design printed with elastic DP 4000 of water based by Gozde Emprime.

The Water-based elastic DP has been printed in favorite emprime with 4000

that is excellent washing fastness,elasticity,coverage,soft and silky touchness

and complies with ecologic standards# inkuin inks

Glow in the dark

• High power of glowing for long period of time while absorbing enough light

• APEO, Lead free formulation

• Non-tacking

• No harmful or distracting odors in the work place

• Use 80-120 t/inch mesh(32-47 t/cm)

• Cure @ 150 c,1.5 min

835 is high density base can be used for color mixing as is.

When 835 high density base is cured it has a opaque matte finish.

Mesh no should use from 83-135 line/inch and print at least 10- 15 rounds

with stencil whose thickness is about 200-300 microns.

Produce amazing 3D results as pictures.